24/7 Customer Service (800) 927-7671

800w ER11 CNC Water Cooled Spindle Motor For engraving milling grind 65x195mm 4 Bearing & 65mm cast aluminium spindle bracket !

100 % of buyers enjoyed this product!
In stock
Sale Price: $ 112.00
45 days Money back
45 days Money back Returns accepted if product not as described, buyer pays return shipping; or keep the product & agree refund with seller.
On-time Delivery
On-time Delivery
Guarantees: On-time Delivery 60 days

Share:

1pcs X 220VAC 0.8KW ER11 Water Cooled Spindle 4 bearings

1pcs X 65mm Cast Aluminium Bracket

Spindle: 0.8KW ER11

Basic parameters:

  • Size:65x195mm

  • Material: 304 stainless steel jacket, water jacket is pressure cast aluminum tubes, high temperature copper coil

  • Speed ways: through the inverter output voltage and adjust the operating frequency can be achieved 0-24000 stepless

  • Cooling: water cooling mode

  • Power Interface: Optional GX16 waterproof air plug, there are marked 1234,

  • 123 were connected to the inverter power supply (U, V, W), 4 connected inverter ground

  • Power:0.8KW

  • Voltage:220VAC

  • Frequency:0-400Hz

  • Speed:0-24000rpm

  • Runout off:less than 0.01mm

  • 4pcs bearing

  • Bearing type:2×7002C P4 DT & 2 ×7000C P4 DT

  • Air Cooling ER11 collet chunk

  • Grease Lubrication

  • Main application: engrave for Wood,bamboo,normal PCB,PVC,PMMA,plastic,bamboo,

duotone board(ABS)and etc nonmetal,also can engrave on gold,silver,copper,

aluminium,Pb etc soft metal surface working,but not milling working

Advantage:

  • Bearing is P4 grade,2×7002C P4 DT &2×7000C P4 DT,Increase spindle life

  • High speed,high torque,low noise,low price.

  • High precision,runout off less than 0.01mm.Coaxial degree less than 0.0025mm

  • Shipment within four days,there is no fake tracking number,make sure that you receive time

Scope:

  • Engrave for Wood,bamboo,normal PCB,PVC,PMMA,plastic,bamboo,duotone board(ABS)and etc nonmetal,also can engrave on gold,silver,copper,aluminium,Pb etc soft metal surface working

Instructions for use:

  • Spindle working environment temperature is usually -10 ~ 40 .

  • Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon.

  • 500V shake table to check the stator insulation resistance of not less than 50MΩ.

  • The internal electric spindle into the base 2,3 inspection meet the requirements, in strict accordance with the electro~spindle mounting position of installation, tighten the screws, not loose in the spindle into the base.

  • Spindle storage or disable power after six months, to be replaced with new grease before re-use, otherwise it will affect the life of electric spindle.

  • Spindle must be supporting the use of inverter, inverter selection should match the voltage, power and frequency range spindle. Set the drive first set reference frequency inverter, inverter reference frequency spindle by the highest frequency settings, such as the reference frequency of the inverter is not set (the reference frequency of the inverter is set to 50Hz at the factory), begins to run electricity spindle immediately burned. Frequency spindle is generally 0 ~ 400Hz, so the reference frequency of the inverter to be set at 400Hz.

  • The three-phase power inverter and electric spindle connection, three-phase inverter welding power cord plug 1 (U1), 2 (V1), 3 (W1) feet, 4 feet for the ground. Then drive to the external power connector. After power inverter jog, observe the direction of rotation of spindle motor spindle indicate whether the same direction as the rotation direction of the inconsistency should be immediately shut down, swap the drive with two electric spindle connected to a three-phase power supply. Spindle prohibited run in the wrong direction of rotation.

  • In order to prolong the life of electric spindle, spindle or new spindle bearings should be replaced with new low 8h after running up speed in the speed range, high speed operation and avoid direct shorten bearing life. On vacation in the future, turn the electric spindle load running half an hour, and then start working.

  • When installing electric spindle collet, should be cleared within the first hole and clean surface dirt collet shaft, so as not to reduce the precision collet assembly and disassembly when not equipped with tools, so as not to damage the tool, note that the clamping clip prohibit excessive force when head.

Cast Aluminium Bracket: 65mm

Diameter :65mm

Material: cast aluminium

Feature:

  • Compared with the aluminium profile fixture,the accuracy is much higher , and it is hard to deform.

  • Inner wall is very smooth, outer walls is sandblasted, relatively fine uniform, but not very smooth,.

  • Cast aluminium fixture is much heavier than aluminium profile fixture

Product Description:

  • Cast aluminium fixture is high quality aluminium which is casting with a special manufacturing process ,compared with ordinary aluminium ,This product has toughness, strong shock resistance, high hardness and strong antioxidant activity.

Usage:

  • Cast aluminium fixture is mainly used for fixation of ancillary products, thereby ensuring the verticality of balancing and ancillary products, ancillary products to improve running accuracy, reduce noise, reduce the accumulated error.

Shipping terms

Our products are sold worldwide.

But if your country is more difficult to transport goods, please contact us in advance to confirm shipping cost.

Payment

We accept paypal credit, bank transfer, western union etc.

Payment must be made within 7days calendar days of the auction end time.

Problems And Feedback

Please give us the opportunity to resolve any problem, we will try our best to help you.

Your satisfaction is very important for our store, so please contact us before you want to leave a negative feedback.

Thanks very much in advance.

Refund

If you are not satisfied with our package like the products is damage, please do not sign it and contact us immediately.

If it is possible, please take some photos or make a small video about it. It will help us to solve the problems.

Note

We can produce the product according to our customer’s design.

Average Star Rating:
0 out of 5 (0 Ratings)
NameRatingFeedback
Shipping CompanyShipping CostEstimated Delivery Time
DHL3 - 7 days
UPS Expedited3 - 7 days
EMS5 - 14 days
Post Air MailFree Shipping15 - 45 days
Return PolicyIf the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.

N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
Seller Service On-time DeliveryIf you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).

Customers Who Bought This Item Also Bought

Price:  $ 112.00 / piece